A package of dynamic, optimized firmware for chip tuning of UAZ vehicles with M86 ECU from Паулюс © Paulus. 2019

Checksums on all versions are fixed to the standard value. That is, tuning is not detected by the currently known reconciliation procedures
software authenticity. (synonym - mapping procedure)

Differences of the "max" versions - even higher available torque
Applicability: the owner’s tendency to get the most out of even a little at a loss of efficiency, the installation of "big wheels", the use of cars in rally raids, etc. etc.

versions of the NI version with the immobilizer disabled. Attention! if there is no scrolling after recording the firmware, set a jumper in the starter relay.
in case of implementation of a starter control circuit variant through a body module on a car, only disabling the immo in PCM is not enough time to start.

GBO-4 versions are single-mode. That is, a reasonable compromise for approaching the optimal phase of the maximum pressure of the cycle of the propane-butane mixture (differences in the combustion phase) with the ability to move on gasoline, without full loads and as accurately as possible, of course. In these versions, the interval of revolutions of active monitoring of misfires is limited.

Download manuals for working with ECU.

Firmware for 1 ID - 300 rubles.
If you want to purchase individual firmwares from the УАЗ с ЭБУ M86 от Паулюс ©Paulus 2019 package, place an order, choose a payment method, and in the comment specify which firmware YOU need.

Buy a set of firmware УАЗ с ЭБУ M86 от Паулюс ©Paulus 2019 (specify the identifier of the required firmware and the amount)

When paying, payment processing takes place on the website of the electronic payment system, which has passed the international certification. This means that your confidential data (card details, registration data, etc.) does not go to the online store, their processing is fully protected and no one can get personal and bank customer data

Download a set of firmware УАЗ с ЭБУ M86 от Паулюс ©Paulus 2019

List of firmware from the kit:

03002_02
03002_02.bin
GBO-4__ 2017_03002_02_E2.bin
Startpower __ 2017_03002_02.bin
Startpower __ 2017_03002_02_E2.bin
Startpower __ 2017_03002_02_max.bin
Startpower __ 2017_03002_02_max_E2.bin
NI
NI_GBO-4__ 2017_03002_02_E2.bin
NI_Startpower __ 2017_03002_02.bin
NI_Startpower __ 2017_03002_02_E2.bin
NI_Startpower __ 2017_03002_02_max.bin
NI_Startpower __ 2017_03002_02_max_E2.bin

03003_05
236021-3763015-00  М86 SW 03003_05.bin
GBO-4_2017_ 03003_05_E2.bin
startpower 2017_ 03003_05.bin
startpower 2017_ 03003_05_E2.bin
startpower 2017_ 03003_05_max.bin
startpower 2017_ 03003_05_max_E2.bin
NI
NI_GBO-4_2017_ 03003_05_E2.bin
NI_startpower 2017_ 03003_05.bin
NI_startpower 2017_ 03003_05_E2.bin
NI_startpower 2017_ 03003_05_max.bin
NI_startpower 2017_ 03003_05_max_E2.bin

ZU03004_06
GBO-4_2018_ZU03004_06_E2.bin
startpower 2018_ZU03004_06.bin
startpower 2018_ZU03004_06_E2.bin
startpower 2018_ZU03004_06_max.bin
startpower 2018_ZU03004_06_max_E2.bin
ZU03004_06.bin
NI
NI_GBO-4_2018_ZU03004_06_E2.bin
NI_startpower 2018_ZU03004_06.bin
NI_startpower 2018_ZU03004_06_E2.bin
NI_startpower 2018_ZU03004_06_max.bin
NI_startpower 2018_ZU03004_06_max_E2.bin
NI_ZU03004_06.bin

ZU03004_07
GBO-4_2018_ZU03004_07_E2.bin
startpower 2018_ZU03004_07.bin
startpower 2018_ZU03004_07_E2.bin
startpower 2018_ZU03004_07_max.bin
startpower 2018_ZU03004_07_max_E2.bin
ZU03004_07.bin
NI
NI_GBO-4_2018_ZU03004_07_E2.bin
NI_startpower 2018_ZU03004_07.bin
NI_startpower 2018_ZU03004_07_E2.bin
NI_startpower 2018_ZU03004_07_max.bin
NI_startpower 2018_ZU03004_07_max_E2.bin
NI_ZU03004_07.bin

Calibration: Паулюс ©Paulus